Wide application of fluidized granulation coating machine: 1) Finishing the coating of the powder to obtain a very high degree of sphericity of the finished product; 2) Finishing the taste and coloration of powder, granules and pills; 3) complete coating and granulation of the powder; 4) Finishing the coating of the powder (pellet), coating, and drying are completed once. 5) The coating process of the finished powder is extremely reproducible; 6) Complete the automatic control of the coating liquid supply volume of the powder, and the temperature in the bed is stable without splashing; 7) The spray coating powder of the finished powder is automatically sprayed, and the measurement is accurate; 8) Finishing the coating of the powder to treat the low density material due to the compaction of the centrifugal force; 9) Complete the coating liquefaction of the powder, which is not easy to agglomerate and adhere; In the current technological development background, there are three technical problems that need to be improved in the current technology development: 1. Air treatment is to be perfected: the fan and the damper are not linked, and air backflow may occur between the fan shutdown and the butterfly valve closing. As the running time increases, the high-efficiency filter will be blocked or damaged. It is recommended that the start and stop of the fan be linked with the switch of the damper. When the fan starts, the damper opens at the same time. When the fan stops running, the damper closes synchronously. There will be no air backflow. 2. Unstable control fluctuation: The air volume control equipment adopts frequency conversion speed control. In the production process, the air volume can only be adjusted manually according to the fluidization state of the material at any time. Therefore, the stability of the air volume and the relatively constant air volume cannot be guaranteed. Changes in the resistance of the filter bag and other factors will affect the stability of the air volume, and the change in air volume can affect the drying speed. This will cause excessive temperature fluctuations that affect the dry granulation quality of the equipment. 3, the size of the particles is not uniform: from the principle of particle formation, the particle size is proportional to the flow rate of the spray, and inversely proportional to the atomization pressure. When the atomization pressure is set to be constant, as the flow rate of the spray liquid increases, the particles become larger; as the flow rate of the spray liquid decreases, the particles become smaller. When the flow rate of the spray liquid is set to be constant, as the atomization pressure increases, the particles become smaller; also as the atomization pressure decreases, the particles become larger. It can be seen that the reasonable combination of the amount of liquid sprayed, the amount of liquid sprayed and the atomization pressure of the inner and outer layers per unit time can produce qualified particles. The atomization angle (fine adjustment) can be adjusted by adjusting the atomization pressure and the outer nozzle on the spray gun head. To be done. Since the inner nozzle has a small aperture and the outer nozzle has a large aperture, the atomization pressure flowing through the outer nozzle must be greater than the inner nozzle pressure. Otherwise, the inner and outer atomization pressures cannot atomize the liquid evenly. Causes uneven particle size. 10000Hz High Frequency LiDAR Module 10000 Hz is one of our 2021 new solutions products,which can be widely used in drone postioning, car anti-collision, intelligent traffic monitoring etc. with high accuracy. We support customized service of different frequency(100hz,200hz,300hz,400hz,1000hz,5000hz,10000hz etc.), you can choose the suitable design. And the LiDAR module is a small size with 43*35*21mm, customers can be integrated to their measure device easily. If you meed any documents(PDF files etc.) of JRT high frequency LiDAR distance sensor, please contact us now. 10000Hz High Frequency LiDAR Module,LiDAR,High Frequency LiDAR Module,10000Hz LiDAR Module Chengdu JRT Meter Technology Co., Ltd , https://www.rangingsensor.com
Some key features may help:
Accuracy: ±3~5cm(<50m) /±1%(>50m)
Range: 0.1-200m
Resolution: 1cm
Frequency: 100/200/400/1k/5k/10khz
Laser type: 905nm,Class I
Size: 43*35*21mm
Weight: 20g
Input voltage: 8-36V