Automatic asphalt mixture mixing machine manual The fully automatic asphalt mixture mixer meets the requirements of JTG E20-2011 << Testing procedures for asphalt and asphalt mixtures for highway engineering >> . It is used for hot mixing of various asphalt mixtures, and it can also be cold mixed with various cement, lime and other mixed materials to replace the artificial fried materials. It is one of the indispensable equipment for the research and development of the laboratory of the scientific research, design and construction department of highway and urban roads. Second, BH-20 new asphalt mixture mixer structure Automatic intelligent asphalt mixture mixer price installation instructions: 1. The asphalt mixture mixer should be installed on a flat and sturdy cement concrete foundation. The foundation thickness should be no less than 20 cm, fastened with expansion screws and leveled. Automatic intelligent asphalt mixture mixer price cleaning and maintenance Fire Hose Reel And Cabinet,Fire Hose Reel ,Hose Reel Drum,Hose Reel Cover NINGBO TOMAN IMP. & EXP. CO., LTD , https://www.tdotmfiresolution.com
The asphalt mixture mixer is heated by an advanced heating device and has high temperature control precision. The heating pot is made of three layers of materials for thermal insulation, and the thermostatic effect is good. The machine can automatically control temperature, timing, automatic mixing, lifting, mixing various particle sizes, no jamming and crushing, easy to operate, easy to master, save time and effort, safe and reliable.
Third, intelligent mixed asphalt mixer | high quality asphalt mixer main technical parameters:
1 , mixing pot zui large capacity: 10L/20L
2 , temperature control range: 0-250 °C arbitrary setting
3 , power supply: AC220V 50HZ
4 , motor power: 550W × 2
5 , heating power: 2kW
6 , the rotation speed of the mixer: 80r / min; revolution speed: 45r / min
2. Power on before use, check each control button on the control panel; rise, fall, stop; time control, temperature control is normal.
3. The power supply has a main switch to turn off the power when the work is completed or during commissioning. And the machine should have good grounding to prevent leakage.
5. Operation steps of asphalt mixture mixer
1. Firstly, preheat the mixer and the mixture according to the requirements of the standard and standard, and then work according to the standard procedures specified in the specification.
2 , turn on the 220V power supply, rotate the power switch; thermostat setting: the temperature setting of the temperature controller is set at the factory, the user does not need to adjust in general, to prevent changing the state, affecting the use; stirring time setting: time control The switch is set to hours, minutes, and seconds. When using, the time switch should be preset in the “ minutes †section, and the lower digital dial can be set to “0200†to mean 2 minutes. After the time is set, press the clear key.
3. Set the heating temperature first, press the stirring switch, then start the lowering button, so that the stirring blade will be lowered while stirring. When the stirring blade is close to the bottom of the mixing pot, stop and stop, enter the normal mixing, stir the time, stir automatically stop. Start the up button to make the stirring system rise and stop automatically. When the second time is stirring, press the clear switch, then press the stirring button and the down button to work automatically.
4. After the material is discharged and the stirring system is raised into position, the heating pot can be turned over by holding the heating pot and turning the handle in one hand and removing the bolt at the bearing. The mixture was scooped out with a spoon and placed in a porcelain dish to prepare a sample as needed.
1. Cleaning: When the mixing is stopped, the power supply must be cut off, the heating pot, the stirring blade and other parts of the machine should be cleaned, and no asphalt residue or dirt should be left.
2 , maintenance: After cleaning, the machine can be maintained, guide column, lifting column and other sports wear parts should be added with appropriate mechanical oil, if not used, should be covered to cover, keep the machine clean.
Seven, intelligent mixing asphalt mixer | high-quality asphalt mixer use precautions
1. Wear protective gloves to prevent burns during operation!
2. When removing the material, the pin at the bearing should be removed. When turning the pan to take the material, carefully handle the material to prevent the hot material from scalding the skin.
3. Set the heating temperature first, press the stirring switch, then start the lowering button, so that the stirring blade will be lowered while stirring. When the stirring blade is close to the bottom of the mixing pot, stop and stop, enter the normal mixing, stir the time, stir automatically stop. Start the up button to make the stirring system rise and stop automatically. When the second time is stirring, press the clear switch, then press the stirring button and the down button to work automatically.
4. After the material is discharged and the stirring system is raised into position, the heating pot can be turned over by holding the heating pot and turning the handle in one hand and removing the bolt at the bearing. The mixture was scooped out with a spoon and placed in a porcelain dish to prepare a sample as needed.