Fruit and Vegetable Powder is a powdered food made from fresh fruits and vegetables through the process of drying, grinding and sieving. It not only retains the nutritional content of fruits and vegetables, but also has the advantages of being portable, easy to store and easy to use. Fruit & Vegetable Powder,Red Raspberry Powder,Red Grapefruit Powder,Freeze Dried Apple Juice Powder Shaanxi Changsheng Industrial Co., Ltd. , https://www.cncsbio.com
Fruit and vegetable powder can be used to make a variety of beverages, food, health products, etc., with increased nutrition, enhance immunity, promote digestion, disease prevention and other effects. Common fruit and vegetable powders include apple powder, blueberry powder, spinach powder, carrot powder, etc.
Health care tablet press mold plays a vital role in the quality of tablets
Before installing the mold for the health product tableting machine , the power of the tablet press must be cut off, the cover plate, the lower rail, the hopper, and the feeder are removed. Open the right door, gradually clean the working surface of the turntable, the die hole and the die for installation, and apply some vegetable oil outside the middle die and the punch to adjust the thickness of the film to 5 or more.
To install the mold in the tablet press, loosen the embossed screw screwed on the upper rail cover, pull out the cover, and tap the middle die with the middle die bar to insert the middle die into the middle die hole. The Chinese model must never be higher than the working surface of the turntable, and should be checked one by one to avoid mistakes. When installing the middle mold, turn the inner test wheel of the lower part of the machine to make the turntable rotate clockwise and then fix it with the middle mold screw.
Install the punch on the tablet press, remove the cover on the upper rail guide, and then gradually insert the upper punch into the hole, rotate the punch with the thumb and forefinger, and check that the head enters the middle mold and slides flexibly. The hard rub phenomenon is acceptable. The upper punch is fully assembled and the cover is fastened.
In the pharmaceutical production process, the mold of the health product tablet press plays a vital role in the quality of the tablet. For example, the punch hole becomes large, causing the punching filler to be uneven, so that the difference in tablet weight does not conform to the regulations or the split is generated; Different lengths, directly affect the weight difference and hardness of the tablet to cause the lobes, or affect the friability; the punch has a curling edge or the punch is not flat, affecting the flaking, causing lobes, sticking and so on. Therefore, in daily management, we must pay attention to the daily maintenance, maintenance and storage of the powder tablet press mold to ensure the quality of our tablets.
The following procedures are expected to help you with the daily maintenance, maintenance and storage of your future health product tablet presses.
1. The newly purchased health care product tableting machine mold is accepted and accepted by the workshop mechanics. After passing the test, the team leader will confirm again.
2. After receiving, the outer packaging should be removed. After removing the anti-rust oil, it should be cleaned and disinfected with 95% ethanol before being stored in the mold for storage. The storage area should be placed according to the model and the type of sheet, and the obvious indication is also provided. .
3. Before use, check whether the specifications of the molds using the health care product tableting machine are consistent with the specifications and models required. Before the mold is installed, use a clean cloth to wipe, and then wipe with 75% ethanol. After the ethanol is evaporated, install it again. During the installation process, check whether the punch and the die are in agreement. Special care should be taken to handle it gently. At the same time, note that the new and old molds should not be mixed. When mixing, the control and influence on the difference of the weight should be evaluated or tested.
4. The mold of the health care product tableting machine should be sent back to the mold management room and cleaned in time. When cleaning, use 95% ethanol. The cleaning process should pay attention to check whether the mold is damaged or not, and the damage can be picked out in time, and the repair can be repaired. Unrepairable workshop mechanics are assessed for scrapping and registration.
5. If the cleaned mold is not used for a long time, it should be coated with a layer of anti-rust oil. When storing, it should be placed according to the model and the type of sheet, and there is obvious indication. The storage process should ensure the temperature and humidity of the room to avoid rusting of the mold of the health care product. If the humidity of the room is too large, the dehumidifier can be turned on to keep it dry, keep the mold clean and dry, and do not store anything other than the mold between the molds.