Anesthesia Medical Co., Ltd. , https://www.jssinoanesthesias.com
2. The transmission mechanism adopts worm gear and worm to directly drive. It has no excessive noise when used, and has sufficient oil storage capacity to get good lubrication.
Structural characteristics and description of CH trough mixer
Structural features
1. This machine is the whole machine base. It has firm structure and stable operation. The mixing paddle and material contact are made of stainless steel. It has good corrosion resistance and keeps the quality and cleanness of the mixture without discoloration.
3. The stirring paddle is active. When replacing the material, only one nut can be removed to remove all the blades and thoroughly cleaned in the tank.
4. This machine controls the automation mechanism controlled by electrical equipment, which is easy to operate and greatly reduces the labor intensity of the operator. A mixing device is attached to the mixing and pouring to ensure safety. With time control. Automatically stop at different times to improve material quality.
Construction description
1. Mixing reducer:
The reducer is the main drive mechanism of the mixer. It is located on the right side of the machine. When working, the motor is driven by the motor in the frame. The worm gear and the worm are driven by the triangle to drive the paddle with a 1:25.5 speed reduction. The worm gear shaft has a hollow shank with fixed keys, which can freely assemble and disassemble the stirring paddle. Two ring screws are mounted on the top of the reducer for installation and disassembly. A screw is installed on the end cover to adjust the positioning of the stirring paddle. It has been adjusted at the factory, and it is generally not necessary to adjust it during use.
2, mixing tank:
The mixing tank is U-shaped and made of stainless steel. It is equipped with a stirring paddle, which is placed on the mixing reducer and the dump reducer. The mixing paddle is a combination of two pieces. Unscrew the hex nut and pull out the center shaft. The paddle can be removed by moving to the left and right. The right end is equipped with a butter cup. It protrudes out of the reversing reducer to lubricate the axis of the paddle.
3, the material reducer:
The reversing reducer is used to control the positioning angle of the mixing tank. It is located on the left side of the machine. When working, the motor is driven by the device, and the V-belt, the transmission worm and the fan-shaped worm wheel drive the mixing groove to rotate in a certain angular range. The mixture is poured out at a time.
4, the base and motor device:
The base is cast as a whole, and the motor is mounted on the movable plate on both sides of the base. The upper and lower sides of the motor can be adjusted by the screw to make the V-belt get a certain tightness and maintain the transmission force. Electrical appliances are installed in the middle door behind the base. The power supply enters the transfer switch from the hole below the base. There are two limit switches on the base to control the angle of the mixing and turning.
5, electrical control box:
This operating box controls the movement of the machine, which is located on the right side of the machine. On the front side is equipped with ammeter, push button switch and red and green indicator light. When the main switch behind the base is opened, the red light will be on, indicating that there is electricity on the line; when the stirring paddle is turned on, the red light is off, indicating that the stirring motor has Normal operation, while the ammeter also indicates the load of the motor. The operation of the stirring paddle can be divided into continuous and timed operation. When the switch is located at a continuous position, the stirring paddle is started to run for a fixed time, and the car stops automatically when the switch is in time. The mixing time can be adjusted in the time relay on the side of the control box. When the start time is required, the switch can be turned on. At this time, the stirring paddle also stops, and the button of the paddle "on" must be clicked again, and the time starts. In order to protect the operation safety, when the upper opening of the mixing tank leaves the upper cover, the above movements are all stopped. At this time, the stirring paddle is operated only when the button is “openedâ€, and the hand is stopped, the rotation of the mixing tank can be “up†of the mixing tank. "Bottom" button, note that the two can not be simultaneously smashed, its rotation angle is controlled by the fiber switch on the organic seat, and the angle is adjusted by the control board at both ends of the mixing tank.